Design and optimization of a cavitating device for Congo red decolorization: Experimental investigation and CFD simulation

The aim of this work is to perform design and optimization of a cavitating device based on CFD simulation. A set of operational and geometrical parameters such as convergence angle, divergence angle, length of throat, and inlet pressure that can affect the hydrodynamic cavitation phenomenon generating in a Venturi are evaluated through CFD simulation and experimental approaches. Response surface methodology (RSM) was employed to achieve the optimum geometrical configuration. The CFD results show that the maximum cavitation zone in the Venturi can be obtained when half angle of the convergence section, throat length and half angle of the divergence section are 22.7°, 4 mm, and 6.5°, respectively. A maximum decolorization of 38.8% has been obtained using the designed Venturi at cavitation number (Cv) of 0.12. Additionally, the results were compared to that of various orifice plates. A decolorization of 26.2% using 33 holes orifice plate and 11.55% in one hole orifice plate approved the superiority of the designed Venturi.     

Electron energy spectrum in the field-ionized plasma

In this article, the effect of ionization on the energy spectrum of electrons within the interaction of a laser pulse with hydrogen atoms is investigated using particle-in-cell simulation codes. The results show that the behaviour of electrons' energy distribution function in the field-ionized plasma, which occurred due to the field ionization, compared with that in the pre-plasma strongly depends on the pulse shape. For short rise-time pulses (here 30 fs), due to the rapid enhancement of laser electric field, ionization occurs quickly, and as a result, there is not much difference in the electron energy in both the media. However, for pulses with rise time of 40 fs, in the pre-plasma state, the electron population reaches higher energies compared with the field-ionized plasma state. The main reason for this difference is the nonlinear wave breaking that happens earlier due to density inhomogeneity in the field-ionized plasma. On the other hand, at longer rise-time pulses (here 60 and 70 fs), electrons achieve higher energies in the field-ionized plasma than those in the case of pre-plasma. In this case, because of density fluctuations in the field-ionized plasma, the Raman backscattered radiations are seeded by a strong initial noise at the earlier times and the Mendonca condition for chaos threshold is met sooner. Therefore, the electrons gain more energy through the stochastic mechanism that is in agreement with chaotic nature of the motion.     

Pure annihilation decay of strange beauty meson into two charm heavy mesons

In this study, the heavy to heavy decay of \begin{document}$ B^0_s\rightarrow D^{*+}D^- $\end{document} is evaluated through the factorization approach by using the final state interaction as an effective correction. Under the factorization approach, this decay mode occurs only through the annihilation process, so a small amount is produced. Feynman's rules state that six meson pairs can be assumed for the intermediate states before the final meson pairs are produced. By taking into account the effects of twelve final state interaction diagrams in the calculations, a significant correction is obtained. These effects correct the value of the branching ratio obtained by the pure factorization approach from \begin{document}$ (2.41\pm1.37)\times10^{-5} $\end{document} to \begin{document}$ (8.27\pm2.23)\times10^{-5} $\end{document}. The value obtained for the branching ratio of the \begin{document}$ B^0_s\rightarrow D^{*+}D^- $\end{document} decay is consistent with the experimental results.     

Application of microcrystalline cellulose as an efficient and cheap sorbent for the extraction of metoprolol from plasma and wastewater before HPLC–MS/MS determination

A dispersive solid-phase extraction method based on a new sorbent has been performed on plasma and wastewater samples to determine metoprolol by high-performance liquid chromatography–tandem mass spectrometry. In this study, the analyte was adsorbed from the samples onto microcrystalline cellulose as a green and efficient sorbent and then eluted for use in the determination step. In the mass spectrometer, the analyte was detected in the positive mode and selectivity of the analysis was increased by sequential mass analysis through multiple reaction monitoring. All of the effective parameters in the extraction of metoprolol from plasma and wastewater were optimized. Under optimal conditions the method was linear in the ranges of 1–1,000 and 0.1–1,000 ng/ml in plasma and wastewater samples, respectively. The detection limits of the method were 0.30 and 0.03 ng/ml in plasma and wastewater samples, respectively. The data showed that the method provides low detection limit, wide linear range, good precision and high extraction recovery. Finally several plasma and wastewater samples were successfully analyzed using the method. The use of a small amount of a green and inexpensive sorbent and a low volume of plasma without the need for further pretreatment steps are the main advantages of the method.     

Rice husk silica as a sustainable filler in the tire industry

In this paper, we studied commercially available precipitated rice husk silica (RHS) with conventional precipitated silica, which has nearly the same surface area, and replaced part of the carbon black with RHS and conventional silica in a basic tread formulation. All formulations were mixed with the same amount of filler during the study. Silica was used at 15, 30 and 50 phr loading, and part of the carbon black was replaced by silica. Compound curing characteristics, physical properties, rebound resilience, heat generation, abrasion loss, dynamic properties and morphology were analyzed. The results indicated that RHS demonstrated compound properties comparable to those of conventional silica. As part of the carbon black was replaced with conventional silica, a slower cure rate, higher rebound resilience, lower heat generation, lower abrasion loss, and lower tan delta were observed with no significant change in physical properties, but some changes in physical properties were observed using one way ANOVA analysis. We found the same trend when replacing part of the carbon black with RHS, such as a slower cure rate, higher rebound resilience, lower heat generation, lower abrasion loss, and lower tan delta with no significant change in physical properties, but some changes in physical properties were observed using one way ANOVA. This sustainable material could be used to replace conventional silica in tire compounding, as well as to replace a portion of carbon black with RHS for improved heat build-up, rolling resistance, and abrasion loss.     

Effect of sodium dodecyl sulfate on CO2 and H2S absorption enhancement of functionalized multiwall carbon nanotubes in water: Experimental study and empirical model

A single bubble absorption column was used to examine the effect of hydrodynamic on carbon dioxide (CO₂) and hydrogen sulfide (H₂S) absorption in pure water and water-based nanofluids dispersed with neat, and OH and NH₂ functionalized multiwall carbon nanotubes (MWCNTs). Sodium dodecyl sulfate (SDS) was used as a surfactant and stabilizer. The maximum absorption of CO₂ and H₂S were found to be 0.0038 mmol/m²·s and 0.056 mmol/m²·s using NH₂-MWCNTs /nanofluid with 0.5 wt% content, respectively. The diffusion coefficients of gases into the nanofluids were computed by using an equation attained based on Dankwert’s theory. A last, an empirical correlation was proposed to determine the Sherwood number for the absorption of the aforementioned gases into the nanofluids.     

Cobalt promoted Ni/MgAl2O4 catalyst in lean methane catalytic oxidation

In the present research, magnesium aluminate spinel was prepared as catalyst support using a novel, facile, and efficient mechanochemical method. The Co-promoted catalysts with 20 wt.% of Ni were fabricated using an impregnation route and the samples were analyzed by the X-ray diffraction (XRD), N₂ adsorption/desorption (BET), temperature-programmed reduction and desorption (H₂-TPR and O₂-TPD), and field emission scanning electron microscopy (FESEM) tests. The results confirmed that all samples have a mesoporous structure with a high specific surface area and the presence of cobalt caused complete CH₄ oxidation at low temperatures, and no side reactions were observed. The results indicated that the 3%Co-20%Ni/MgAl₂O₄ catalyst was the optimal sample among the prepared catalysts, owing to the improvement of reduction features and oxygen mobility. The 50 and 90% of methane conversion was obtained at 530 and 600 °C, respectively. Also, the influence of calcination temperature, GHSV, and feed ratio was determined on the catalytic activity. The obtained outcomes revealed that the calcination temperature has a significant effect on the textural properties and catalytic efficiency. The sample calcined at 700 °C showed the weakest performance, which was related to the sintering of particles at high temperatures. The catalytic stability showed that the 3%Co-20%Ni/MgAl₂O₄ has acceptable stability during 600 min time of reaction.

Graphical abstract

     

Left dihedral codes over finite chain rings

Let R be a finite commutative chain ring, $D_{2n}$ be the dihedral group of size 2n and $R[D_{2n}]$ be the dihedral group ring. In this paper, we completely characterize left ideals of $R[D_{2n}]$ (called left $D_{2n}$-codes) when $\gcd (char(R),n)=1$. In this way, we explore the structure of some skew-cyclic codes of length 2 over R and also over $R\times S$, where S is an isomorphic copy of R. As a particular result, we give the structure of cyclic codes of length 2 over R. In the case where $R={\mathbb{F}}_{p^m}$ is a Galois field, we give a classification for left $D_{2N}$-codes over ${\mathbb{F}}_{p^m}$, for any positive integer N. In both cases we determine dual codes and identify self-dual ones.